We don’t do a lot of printing and since We have become a laptop only household printing has been further discouraged since going to the printer and plugging in is simply too much effort, I just save/print it to a PDF.

So after finally setting my printer as a network printer, using an old laptop, I was dismayed to find that the printer was not printing the first page correctly, the printing would start almost halfway down the page, strangely however subsequent pages of each job were printing just fine.

The printer is a Kyocera FS-1010, laser printer.

After some searching around the web I found a few people reporting the same symptoms:
http://www.fixya.com/support/t1083180-huge_margin_kyocera_fs_1000

But then I came across these threads on copytechnet forums:
http://www.copytechnet.com/forums/kyocera/15980-kyocera-fs1010-delayed-printing-1st-page-2.html#post55451

Basically there are some foam pads that insulate some moving arms from their stop point. These get compressed over time and no longer insulate the arms and they get magnetically stuck on the stop points.

The steps from this post are :

1. Open the right side of the printer
2. Disconnect all connections to engine board
3. Remove engine board
4. Remove plastic guard (white)
5. remove all 3 solenoids
6. Replace all pads on the solenoids that come up against stops
7. Registration Solenoid has 2 pads (1 against the solenoid frame and the other on a stop arm, the others just the frame pad)
8. Keep thickness to around .4 – .5mm Too thick on register arm will cause early printing.
9. Reassemble

So with the above and a service manual downloaded from : http://www.eserviceinfo.com/downloadsm/16172/Kyocera_FS-1010.html

I was able to open the printer, access the solenoids scrape off the old foam and glue some thin cardboard in their place.

After a successful ’Step 9′ Reassemble, printing is back to normal!

There aren’t many items in this tech would that can be fixed so easily simply, Of course opening up a printer and removing bits a pieces is not usually regarded as easy.

Note: There have been a few people leaving comments asking how to get their camera working, I’m sorry but I don’t have any answers for you as I only have the one Logitech camera and I haven’t played with any new drivers since i got it to work! I hope you can find the solution.

—–

When I attempted to attach my “Logitech Quickcam for Notebooks Pro” (older version see pic) webcam to by Vista laptop, I was unable to find a driver for it. Logitech have decided to only release Vista drivers for webcams released in the last 3 years. I call that a real poor move. In fact it stinks of profiteering. When you look for Vista drivers they actually try to sell you one of their new and apparently Vista compatible models. “This Camera will not work with Windows Vista. Please see our list of newer Vista compatible cameras”.

My webcam works perfectly and has done since I bought it, it’s a great product, as with most of Logitechs gear, but the decision to not release Vista drivers will certainly cause me to shop around a little more next time.
Never fear: I got my Webcam to work using XP drivers in Vista in a couple of very easy steps!
(the ease of this makes Logitechs decision even harder to swallow)

1. First download and Install the latest Vista QuickCam software from Logitech currently “QuickCam 11.0″, you can get it by choosing the current model notebooks pro. When it sits there asking you to plug in your webcam, just close it down, it won’t find the old one.
2. Also Download the old XP software, currently version 8.4.8 build 1034A, we only want the drivers from this package so…
3. Run the install but cancel it when it gives you the first screen of the install, It should leave the decompressed package for you to pick the drivers out of. It will decompress the driver files to “C:\Program Files\Logitech\QuickCamWebInstall”
4. So now you can plug in your webcam and Windows should prompt you to locate a driver. If you have already plugged it in and dismissed that driver wizard, go to the device manager, find the “Unknown Device” ( hopefully you only have 1!), and choose to “Update the Driver”
5. When it asks where the driver is, tell it to look in the folder where the decompressed XP package. It should be at “C:\Program Files\Logitech\QuickCamWebInstall\Drivers\WinNew”
6. That’s it!, Vista should install you webcam successfully and the latest Quickcam software should work perfectly with the Webcam.

Good Luck with it, while I can’t be sure I bet this works for almost all their cameras.